sat-integral.org.ua

Список каналов 4w, 5e, 13e, 36e для Sat-Integral T-9000 HD/T-9100 HD по 2.32

Цитата: Roman от 17 марта 2014, 21:20:58

Цитата: melan от 17 марта 2014, 20:06:44
Наверное, что то не так делаете. У меня тюнер вообще не запускался. После сброса в заводские настройки через COM порт всё заработало.

Давайте по подробней опишите работу с Hyper терминалом.

Цитата: Roman от 17 марта 2014, 18:53:48

...1. Войдите в консоль восстановления...

Все делаю как вы описали кроме как не отправляется команда на ресивер.
Терминал выдает такую картину


turn off boot console early0

--------------------------------------------------------------------
-- Generic Primary Bootloader 88.88-8888, NI (10:14:27, Jul  6 2010)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 1 (expecting 2)
Poly10: 0x860756E3
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 8192 rows: 64 MBytes
SIF1: 512 cols x 8192 rows: 64 MBytes
DRAM: 200 MHz, 2 x 64 MBytes: 128 MBytes
NAND: RDY polling disabled
NAND: (2076) ST SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 227133 uSec


U-Boot 1.2.0.0425_a (Secondary Bootloader) (Dec 29 2011 - 08:35:38)

CPU: PNX?
Secure boot: disabled
DRAM: 128 MB
NAND: nCS0 (force asserted legacy mode)
NAND: ST Micro 64MiB 3,3V 8-bit
NAND 0x03224000: bad block
init hdmi on i2c 1 bus.
--------------------CAT6612 reg 0x1 = 0xca, *************
Net: ip3902
Board Opts: EthOsc HDMI PAL
Splash: done
u-boot startup time so far: 1088 msec
Hit any key to stop autoboot-----:  0
Boot mode is :

Loading from 64MiB 3,3V 8-bit, offset 0x1020000
Automatic boot of image at addr 0x80800000 ...
## Booting image at 80800100 ...
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    1616584 Bytes = 1.5 MB
   Load Address: 80001000
   Entry Point:  802be420
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.24.7_nxp.STB236_NANDflash_HDdecoding_128M_Huangpu.0425_a (Andy
Wong@bogon) (gcc version 4.2.1) #205 PREEMPT Mon Jul 16 16:08:21 CST 2012
console [early0] enabled
CPU revision is: 00019068 (MIPS 4KEc)
Determined physical RAM map:
memory: 02e8c000 @ 00000000 (usable)
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->    11916
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->    11916
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 11823
Kernel command line: mtdparts=gen_nand:128k(Boot0),1M(Boot1),512k(Env),2M(K0),12
M(FS0),512k(U0),3M(K1),33M(FS1),3M(U1),7M(U2) ip3902.mac_address=00:13:8f:60:84:
5f ip=192.168.0.52:192.168.0.51::::eth0 root=/dev/mtdblock_robbs7 ro rootfstype=
cramfs
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
Synthesized clear page handler (26 instructions).
Synthesized copy page handler (46 instructions).
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU clock is 320 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 42592k/47664k available (2822k kernel code, 5072k reserved, 678k data, 1
28k init, 0k highmem)
SLUB: Genslabs=6, HWalign=16, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 64 bytes
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interfac driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
JFFS2 version 2.2. (NAND) В© 2001-2006 Red Hat, Inc.
async_tx: api initialized (async)
io scheduler noop registered (default)
Serial: PNX8XXX driver $Revision: 1$
pnx8xxx-uart: ttyS0 at MMIO 0xb7e0b000 (irq = 11) is a PNX8XXX
loop: module loaded
PNX8335 AES: loaded
NXP ip3902 10/100 Ethernet platform driver irq 60 base b7e2f000
Linux video capture interface: v2.00
pwc: Philips webcam module version 10.0.13 loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCV
C830/840.
pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10
and MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and
VCS-UM100.
usbcore: registered new nterface driver Philips webcam
Driver 'sd' needs updating - please use bus_type methods
NAND device: Manufacturer ID: 0x20, Chip ID: 0x76 (ST Micro NAND 64MiB 3,3V 8-bi
t)
Scanning device for bad blocks
Bad eraseblock 3209 at 0x03224000
10 cmdlinepart partitions found on MTD device gen_nand
Creating 10 MTD partitions on "gen_nand":
0x00000000-0x00020000 : "Boot0"
0x00020000-0x00120000 : "Boot1"
0x00120000-0x001a0000 : "Env"
0x001a0000-0x003a0000 : "K0"
0x003a0000-0x00fa0000 : "FS0"
0x00fa0000-0x01020000 : "U0"
0x01020000-0x01320000 : "K1"
0x01320000-0x03420000 : "FS1"
0x03420000-0x03720000 : "U1"
0x03720000-0x03e20000 : "U2"
pnx833x-ehci pnx833x-ehci: PNX833x EHCI
pnx833x-ehci pnx833x-ehci: new USB bus registered, assigned bus number 1
pnx833x-ehci pnx833x-ehci: irq 40, io mem 0xb7e19000
pnx833x-ehci pnx833x-ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using pnx833x-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
i2c-pnx0105: registered device at 0xb7e0d000
i2c-pnx0105: registered device at 0xb7e0e000
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hci_usb
Bluetooth: Virtual HCI driver ver 1.2
nxp-aes driver : loaded
nxp-adma DMA driver irq 32 base b7e1c000
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
turn off boot console early0

--------------------------------------------------------------------
-- Generic Primary Bootloader 88.88-8888, NI (10:14:27, Jul  6 2010)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 1 (expecting 2)
Poly10: 0x860756E3
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 8192 rows: 64 MBytes
SIF1: 512 cols x 8192 rows: 64 MBytes
DRAM: 200 MHz, 2 x 64 MBytes: 128 MBytes
NAND: RDY polling disabled
NAND: (2076) ST SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 227133 uSec


U-Boot 1.2.0.0425_a (Secondary Bootloader) (Dec 29 2011 - 08:35:38)

CPU: PNX?
Secure boot: disabled
DRAM: 128 MB
NAND: nCS0 (force asserted legacy mode)
NAND: ST Micro 64MiB 3,3V 8-bit
NAND 0x03224000: bad block
init hdmi on i2c 1 bus.
--------------------CAT6612 reg 0x1 = 0xca, *************
Net: ip3902
Board Opts: EthOsc HDMI PAL
Splash: done
u-boot startup time so far: 1088 msec
Hit any key to stop autoboot-----:  0
Boot mode is :

Loading from 64MiB 3,3V 8-bit, offset 0x1020000
Automatic boot of image at addr 0x80800000 ...
## Booting image at 80800100 ...
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    1616584 Bytes = 1.5 MB
   Load Address: 80001000
   Entry Point:  802be420
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.24.7_nxp.STB236_NANDflash_Ddecoding_128M_Huangpu.0425_a (AndyW
ong@bogon) (gcc version 4.2.1) #205 PREEMPT Mon Jul 16 16:08:21 CST 2012
console [early0] enabled
CPU revision is: 00019068 (MIPS 4KEc)
Determined physical RAM map:
memory: 02e8c000 @ 00000000 (usable)
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->    11916
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->    11916
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 11823
Kernel command line: mtdparts=gen_nand:128k(Boot0),1M(Boot1),512k(Env),2M(K0),12
M(FS0),512k(U0),3M(K1),33M(FS1),3M(U1),7M(U2) ip3902.mac_address=00:13:8f:60:84:
5f ip=192.168.0.52:192.168.0.51::::eth0 root=/dev/mtdblock_robbs7 ro rootfstype=
cramfs
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
Synthesized clear page handler (26 instructions).
Synthesized copy page handler (46 instructions).
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU clock is 320 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 42592k/47664k available (2822k kernel code, 5072k reserved, 678k data, 1
28k init, 0k highmem)
SLUB: Genslabs=6, HWalign=16, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 64 bytes
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.4 (008/08/26) Phillip Lougher
JFFS2 version 2.2. (NAND) В© 2001-2006 Red Hat, Inc.
async_tx: api initialized (async)
io scheduler noop registered (default)
Serial: PNX8XXX driver $Revision: 1$
pnx8xxx-uart: ttyS0 at MMIO 0xb7e0b000 (irq = 11) is a PNX8XXX
loop: module loaded
PNX8335 AES: loaded
NXP ip3902 10/100 Ethernet platform driver irq 60 base b7e2f000
Linux video capture interface: v2.00
pwc: Philips webcam module version 10.0.13 loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCV
C830/840.
pwc: Also upports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 a
nd MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and
VCS-UM100.
usbcore: registered new interface driver Philips webcam
Driver 'sd' needs updating - please use bus_type methods
NAND device: Manufacturer ID: 0x20, Chip ID: 0x76 (ST Micro NAND 64MiB 3,3V 8-bi
t)
Scanning device for bad blocks
Bad eraseblock 3209 at 0x03224000
10 cmdlinepart partitions found on MTD device gen_nand
Creating 10 MTD partitions on "gen_nand":
0x00000000-0x00020000 : "Boot0"
0x00020000-0x00120000 : "Boot1"
0x00120000-0x001a0000 : "Env"
0x001a0000-0x003a0000 : "K0"
0x003a0000-0x00fa0000 : "FS0"
0x00fa0000-0x01020000 : "U0"
0x01020000-0x01320000 : "K1"
0x01320000-0x03420000 : "FS1"
0x03420000-0x03720000 : "U1"
0x03720000-0x03e20000 : "U2"
pnx833x-ehci pnx833x-ehci: PNX833x EHCI
pnx833x-ehci pnx833x-ehci: new USB bus registered, assigned bus number 1
pnx833x-ehci pnx833x-ehci: irq 40, io mem 0xb7e19000
pnx833x-ehci pnx833x-ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using pnx833x-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
i2c-pnx0105: registered device at 0xb7e0d000
i2c-pnx0105: registered device at 0xb7e0e000
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hci_usb
Bluetooth: Virtual HCI driver ver 1.2
nxp-aes driver :loaded
nxp-adma DMA driver irq 32 base b7e1c000
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
turn off boot console early0

--------------------------------------------------------------------
-- Generic Primary Bootloader 88.88-8888, NI (10:14:27, Jul  6 2010)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 1 (expecting 2)
Poly10: 0x860756E3
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 8192 rows: 64 MBytes
SIF1: 512 cols x 8192 rows: 64 MBytes
DRAM: 200 MHz, 2 x 64 MBytes: 128 MBytes
NAND: RDY polling disabled
NAND: (2076) ST SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 227133 uSec


U-Boot 1.2.0.0425_a (Secondary Bootloader) (Dec 29 2011 - 08:35:38)

CPU: PNX?
Secure boot: disabled
DRAM: 128 MB
NAND: nCS0 (force asserted legacy mode)
NAND: ST Micro 64MiB 3,3V 8-bit
NAND 0x03224000: bad block
init hdmi on i2c 1 bus.
--------------------CAT6612 reg 0x1 = 0xca, *************
Net: ip3902
Board Opts: EthOsc HDMI PAL
Splash: done
u-boot startup time so far: 1088 msec
Hit any key to stop autoboot-----:  0
Boot mode is :

Loading from 64MiB 3,3V 8-bit, offset 0x1020000
Automatic boot of image at addr 0x80800000 ...
## Booting image at 80800100 ...
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    1616584 Bytes = 1.5 MB
   Load Address: 80001000
   Entry Point:  802be420
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.24.7_nxp.STB236_NANDflash_HDdecoding_128M_Huangpu.0425_a (Andy
Wong@bogon) (gcc version 4.2.1) #205 PREEMPT Mon Jul 16 16:08:21 CST 2012
console [early0] enabled
CPU revision is: 00019068 (MIPS 4KEc)
Determined physical RAM map:
memory: 02e8c000 @ 00000000 (usable)
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->    11916
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->    11916
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 11823
Kernel command line: mtdparts=gen_nand:128k(Boot0),1M(Boot1),512k(Env),2M(K0),12
M(FS0),512k(U0),3M(K1),33M(FS1),3M(U1),7M(U2) ip3902.mac_address=00:13:8f:60:84:
5f ip=192.168.0.52:192.168.0.51::::eth0 root=/dev/mtdblock_robbs7 ro rootfstype=
cramfs
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
Synthesized clear page handler (26 instructions).
Synthesized copy page handler (46 instructions).
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU clock is 320 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 42592k/47664k available (2822k kernel ode, 5072k reserved, 678k data, 12
8k init, 0k highmem)
SLUB: Genslabs=6, HWalign=16, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 64 bytes
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
JFFS2 version 2.2. (NAND) В© 2001-2006 Red Hat, Inc.
async_tx: api initialized (async)
io scheduler noop registered (default)
Serial: PNX8XXX driver $Revision: 1$
pnx8xxx-uart: ttyS0 at MMIO 0xb7e0b000 (irq = 11) is a PNX8XXX
loop: module loaded
PNX8335 AES: loaded
NXP ip3902 10/100 Ethernet platform driver irq 60 base b7e2f000
Linux video capture interface: v2.00
pwc: Philips webcam module version 10.0.13 loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCV
C830/840.
pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10
and MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and
VCS-UM100.
usbcore: registered new interface driver Philips webcam
Driver 'sd' needs updating - please use bus_type methods
NAND device: Manufacturer ID: 0x20, Chip ID: 0x76 (ST Micro NAND 64MiB 3,3V 8-bi
t)
Scanning device for bad blocks
Bad eraseblock 3209 at 0x03224000
10 cmdlinepart prtitions found on MTD device gen_nand
Creating 10 MTD partitions on "gen_nand":
0x00000000-0x00020000 : "Boot0"
0x00020000-0x00120000 : "Boot1"
0x00120000-0x001a0000 : "Env"
0x001a0000-0x003a0000 : "K0"
0x003a0000-0x00fa0000 : "FS0"
0x00fa0000-0x01020000 : "U0"
0x01020000-0x01320000 : "K1"
0x01320000-0x03420000 : "FS1"
0x03420000-0x03720000 : "U1"
0x03720000-0x03e20000 : "U2"
pnx833x-ehci pnx833x-ehci: PNX833x EHCI
pnx833x-ehci pnx833x-ehci: new USB bus registered, assigned bus number 1
pnx833x-ehci pnx833x-ehci: irq 40, io mem 0xb7e19000
pnx833x-ehci pnx833x-ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using pnx833x-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
i2c-pnx0105: registered device at 0xb7e0d000
i2c-pnx0105: registered device at 0xb7e0e000
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hci_usb
Bluetooth: Virtual HCI driver ver 1.2
nxp-aes driver : loaded
nxp-adma DMA driver irq 32 base b7e1c000
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
turn off boot console early0

Цитата: Павел от 17 марта 2014, 14:51:01
1.пробуй отключить на время антенну,как будет реагировать.
2.сделай сброс в заводские
3.найди на форуме ПО  T-9100 HD  2.30,залей

Отключение антенны никак не влияет.
Как сделать сброс если не реагирует на пульт???
Залил ПО  T-9100 HD  2.30, результат тот же - на экране заставка "Sat-Integral" и перезагрузы.
Может както через COM порт можна.

После обновления списка каналов, ресивер постоянно перезагружается (наверное был битый файл), на экране телевизора только загрузочная заставка, пробовал обновить софт через USB, обновляется, процес идет, пишет -END-, но чуда не происходит, ресивер всеравно постоянно перезагружается. На кнопки пульта и передней панели не реагирует. Что делать???